Bingham Equipment Company, Arizona
Mesa
(480) 969-5516
1655 S. Country Club Dr.
Mesa, Arizona 85210
Casa Grande
(520) 836-8700
815 W. Gila Bend Hwy.
Casa Grande, Arizona 85122
Yuma
(928) 726-4701
3214 E. Gila Ridge Rd. #1
Yuma, Arizona 85365
Parker
(928) 669-9271
1320 Geronimo
Parker, Arizona 85344
Buckeye
(623) 853-1000
710 N. 195th Ave.
Buckeye, Arizona 85326
Cottonwood
(928) 646-5388
2694 S. Union Drive
Cottonwood, Arizona 86326
Tucson
(520) 887-7799
5225 N. Casa Grande Hwy.
Tucson, Arizona 85743
Phoenix
(623) 850-6000
21828 N. 7th St.
Phoenix, Arizona 85024
Prescott Valley
(928) 350-4295
10123 AZ-69
Prescott Valley, Arizona 86314
Roll
(928) 785-3319
4838 S. Avenue 38 E
Roll, Arizona 85347
Lakeside
(928) 251-0403
5819 HWY 260
Lakeside, Arizona 85929

New Holland H6830 Side-Pull

New Holland H6830 Side-Pull for sale at Bingham Equipment Company, Arizona

Double tap to zoom

New Holland H6830 Side-Pull for sale at Bingham Equipment Company, Arizona

 

Features

A NEW LEVEL OF DISC MOWER PRODUCTIVITY.
The eight-disc heavy-duty H6830 pull-type disc mower combines the benefits of a wide 10-foot, four-inch cut with easy hookup and a low horsepower requirement.


IN-FIELD FLOTATION
The H6830 header is suspended from the main frame of the machine. Large flotation springs allow the header to float both vertically and laterally for even cutting in uneven terrain, preventing damage and bulldozing. You can adjust the flotation spring tension easily by turning the anchor bolts.

TIGHT TURNING, NARROW 10’10” TRANSPORT
The primary PTO uses an 80-degree constant velocity joint that permits tight turning. A secondary CV driveline option allows you to mow in the transport position to “steer” around field obstacles on the fly. Hydraulic tongue swing allows you to power the machine from transport to operating position and back. End shields flip up for a narrow 10-foot, 10-inch transport width.

WIDE 95-INCH SWATH
Wheels are located inboard of the cutting edge to eliminate run-down of uncut crop. Crop deflectors direct the cut crop inside the tire path and into a wide 95-inch swath.

Specifications

H6830 Side Pull  
Cutter Bar  
Cutting width ft. in. (mm) 10' 4" (3150)
Cutting height in. (mm) 0.95-3.25 (24-82.5)
Cutter bar tilt angle degrees 0 to -10
Cutter bar operating range degrees +18 to -28
Breakaway angle degrees NA
Cutter bar floatation Vertical adjustable spring
Type cutterbar MowMax™ cutterbar, modular, w/individual sealed reservoirs
Number of discs 8
Knives per disc 2
Disc cutting diameter in. (mm) 19.7 (500)
Disc drive Bevel gears in sealed modules
Disc speed RPM 2,835
Cutter bar gear protection Std. ShockPRO: easy replace ShockPRO hub with a partial complement of sacrificial splines
Swath width, approx standard** in. (mm) 95 (2413)
Swath width with optional swathboards** in. (m) N/A
Driveline  
Minimum PTO horsepower required hp (kW) 60 (44.7)
Input speed RPM 540
PTO shaft spline/size required 6-spline/ 1-3/8"
Driveline protection Slip clutch
Overrunning clutch Standard
Belt tension N/A
Hydraulics and Hitch  
Hydraulic circuits required Two remotes
Minimum relief pressure required psi (bar) 1,500 (104)
Hitch Category II drawbar
Dimensions and Weight  
Overall width in. (mm) 196 (4978)
Overall length in. (mm) 183 (4648)
Height - transport position* in. (mm) 62 (1575)
Weight, shipping lb. (kg) 3,035 (1379)
Weight, operating lb. (kg) 2,610 (1186)
Maximum transport speed 20 mph/ 32.2 kph
Tires/wheels 27 x 9.5 x 15 6 PR